WOLFTEETH 510 RDA Clone Rebuildable Dripping Atomizer Dual Coil US1 24mm | High Borosilicate Glass Temperature Resistant (Black/Nicotine Free 123703)

This clone of the Hadaly 22mm RDA is only a fraction of the cost of the original. It doesn't come with a squonk (bottom feed) pin although spare o-rings, post screws and 2 coils are supplied.The finish is a bit rough, and there are a few sharp edges in places. What is most concerning is there was some metal swarf still attached to the deck air flow holes, and if this had come loose, metal could be potentially inhaled or swallowed. That is a good reason why all tanks etc. should be stripped down, thoroughly cleaned and inspected before use.The insulator itself is not peak material from what I can tell, just plastic. Other than the points mentioned, the dripper is of reasonable quality for the price. You can use a 510 drip tip of your choice with this atomiser.Flavour wise, it is comparable to the Oumier Wasp Nano and is easy to build with, and is only let down by poor quality control.

Even tho it's branded Wolfteeth RDA, it's not made by Wolfteeth, But that is not misleading they are just advertising the RDA, i would however say that for the price you would be very hard pressed to get this RDA for a better price in the uk. I own around 30 RDA's and this has got to be the best quality clone/styled £ for £ i have ever bought.

This is just perfect. Exactly the same as the original Goon at a huge fraction of the price. The only downside was that the screws were too short, but then I noticed it comes with longer screws so that issues dissappeared immediately. Absolutely love it!!!

I have mixed feelings about this RDA. It appears to be well made, and came with cotton, 2 coils, spare screws and 0 rings. My only issues are that the coils are very difficult to attach to the screws (the legs must be wound round an outer screw and the inner brass-coloured screw, and then tighten the screws down) and I managed to blow both my coils immediately. Thats probably my own fault, but was frustrating as I'm now waiting on my wire before I can properly test this product--UPDATE--After light testing I'm having to conclude that this RDA is substandard and for that I'm dropping my review to 2 stars.Its difficult to attach your coils, as screwing the wire down can cause them to break. The central pillar is also very fiddly and awkward to attach multiple coils to. Once I finally managed to attach my coils and wired the thing up, I discovered the air holes are too small and limit the air-flow, producing a rather feeble amount of vapor (when compared to my cleito aspire 0.2 ohm which I regularly use) If you're a first time builder, I wouldn't recommend this and even if you are I probably wouldn't recommend it either.Visually it looks nice.

For the price, this is a quality RDA. The machining on it is actually pretty good compared to other clones, but then again the deck isn't complex. Here's a brief rundown :Pros -Massive build deck, you can fit some huge fancy coils in this for a 24mmGood quality, materials used seem to be of good standard, although I've only had it for a couple daysCons -Topcap is extremely loose, prone to falling off at times once juice is on thereThe drip-tip that comes with this is extremely wide-bore, however I think any 810 drip-tip will fit, it's all subjective anyway.

People sometimes speak ill of clones, and sometimes it's clear why. My first dabble in the world of rebuildable atomisers was what I believe was a clone. A twisted messes 24, it cost £10 from a local vape shop and I like it. But the build quality simply can't compete with this goon. I read the reviews of the real thing first. Followed by the reviews of the clone here on amazon, the good and the bad. My experience with this clone has been 100% spot on. The finish on the paint, the engraving, the clamps (so easy to build on). The main thing that set this apart from my first rda though, was the o rings. This thing just slides together and apart effortlessly. I no longer worry that this time I slide the cap onto my deck will be the last because of horrible rough o rings.

Good quality clone, very easy to put a build into and the vape quality is excellent. Barrel section does get quite hot fairly quickly but most rda's are the same. Screws holding the clamps in place are ok but not sure how long they will last as they don't seem to be the most durable. Sqounking pin works great and the RDA is perfect for use with a sqounk device as the air intakes are quite high up the barrel so it is pretty hard to over sqounk. Overall I think this is a great RDA for the price.

Been using it a day and no issues. This is my first RDA and I'm really pleased with and wondering why I haven't done it sooner after nearly 5 years of vaping. Lovely smooth hit, the airflow is really, really good. Good for first time drippers as well. I thought the flavour with mesh coils was excellent but with this its quite a bit better. I'm only using the pre-maid coils and the cotton that came with it at the moment but once I use better coils and cotton I have a feeling it's going to be a lot better. Will update in a couple of weeks.It hasn't been a couple of weeks but I'll update any way.Absolutly love it. Apart from the coils that came with it, they we're not worth a w**k same goes for the cotton. Have some Alien Clapton .45ohm coils and firebolt cotton coming and then I'll be happy.